TiLite ZR Rigid Titanium Wheelchair

Frame Style:

Z2FS2 ❑ ZRA Titanium Frame (Full Adjustability. 265 Pound Weight Limit. Weight Limit is restricted to 150 pounds on chairs with Rear Seat Width (A) and Seat Depth (B) from 10”x10” to 12”x12”.) $4,050

Z2FS1 ❑ ZR Titanium Frame Ultimate TiFIT (ZRA Titanium Frame required. Minimal Adjustability. 265 Pound Weight Limit. Weight Limit is restricted to 150 pounds on chairs with Rear Seat Width (A) and Seat Depth (B) from 10”x10” to 12”x12”.) $435

Frame Options:

Transport Brackets:

The TiLite ZR with Wheelchair Transport Bracket Option (Z2WTB) was NOT crash-tested in accordance with ISO 7176-19 or ANSI/RESNA WC19.
Therefore, the Wheelchair Transport Bracket Option is intended ONLY to secure an unoccupied wheelchair in a motor vehicle. The U.S. Department of
Transportation has not approved any tie-down system for transportation of a user while in a wheelchair in a moving vehicle of any type. It is TiLite’s position
that users of wheelchairs should be transferred into appropriate seating in motor vehicles and use the restraints made available by the auto industry.

Anodized Colors

Rear Seat Width: (A)

Measure from outside of seat tube at back post to the outside of the opposite seat tube at back post.

Front Seat Width: (T)

Measure from inside of front frame tube to inside of opposite front frame tube.

Seat Depth: (B)

Measure from front of back post to the front edge of seat sling. Front edge of seat sling will be at the beginning of the bend at front of chair frame, unless Glide™ or 90° Front Angle is ordered, in which case front edge of seat sling begins approximately 1” behind the bend.

Ergo Seat:

Measure from front of back post to begining of upward bend of seat tube.

Front Seat Height: (C)

Measure from floor to top of seat tube at beginning of bend.

Rear Seat Height: (D)

Measure from floor to top of seat tube at back post.

Front Angle (L) or Overall Frame Length (M):

Front Angle (L): Measure from frame front to floor.

Overall Frame Length (M): Measure from front of backrest to
Front Edge of Footrest.

Seat to Footrest: (E)

Measure from front edge of seat sling to top rear of footrest. Measurement must be at least 2” shorter than Front Seat Height (C).

Footrest Width: (I)

Find your Rear Seat Width (A) in the chart below and select one of the options to the right. Measure from inside of front frame tube to inside of opposite front frame tube.

ZFE2 – V-FRONT END (V)
Measure from inside of front frame tube to inside of opposite front frame tube 2-1/2” above footrest. (Required with Front Seat Taper T. Titanium Footrests have 1” of adjustment up and down.) $280

Back Upholstery

Seat Upholstery

Push Handles

Back Height Range: (F)

Back Height: (F)

Seat Back Rigidizer Bar:

ZSB12 – 4” Deep Backrest Rigidizer Bar (Required for Heavy Duty Frame. Available with Aluminum backrest option. Not available with a Non-Folding, Fixed Height Titanium Seat Back type. 4” Deep Rigidizer Bar is NOT a rounded style rigidizer bar.)

ZSB16 – Depth Adjustable Back/Frame (Seat Depths B of 10”-18” allow 2” of rearward adjustment. Height Adjustable Push Handles have a limited Height range with Depth Adjustable Back. Not Available with 19” or 20” Seat Depths B, Heavy Duty Edition, Tension Adjustable by Straps Seat Upholstery or Carbon Fiber Side Guards)

Z2SB13 – Custom Height Backrest Rigidizer Bar (The Standard Rigidizer Bar height is 5” above the Seat Sling for a short, 6” for a medium and 10” for a tall. Custom Height Rigidizer Bar must be at least 4-1/2” above Seat Sling. Maximum Height is 3” less than Lowest Seat Back Height without push handles.)

Seat Back Angle: (G)

Measure angle from front of back post to floor. 90° will be perpendicular to the floor. To approximate the angle from the back post to the seat, subtract 2 degrees from measurement (G) for every 1/2” of dump.

Center of Gravity: (H)

Measure from front of back post at the seat tube to the center of the rear axle. If no center of gravity is selected, chair will ship with the center of gravity in the rearward-most position.

Camber: (K)

Rear Wheel Spacing: (J)

Measure from outside of seat back post to inside of rear tire. 3/4” Rear Wheel Spacing not available with 0° or 2° Camber (K).

Forks

Rear Wheels

Axles

Rear Tires:

Handrims:

Wheel Locks:

Side Guards:

Armrests

Anti-Tips